Ultra Minimalist Duplex AC Outlet
A good-sounding AC wall outlet can be one of the biggest bang-for-the-buck upgrades in audio. Compared to the most highly
touted $200+ outlets, our AC outlet reduces the plastic insulator mass by a factor of three, reduces contact strip thickness
by two, eliminates all plating, and breaks new ground with two features. Our outlet casings are made from a far better
sounding polymer than the high-loss, glass-filled nylon used by all the big bucks outlets. And--our Amish-made Ambrosian
maple faceplate eliminates the high dielectric absorption losses of plastic faceplates, as well as the high eddy current
losses of metal ones.
Physical Principles and Design Concept
An AC wall outlet has four major components. Our listening experiments demonstrate that each one affects sound quality significantly, as follows:
• Insulator Body: The lower the dielectric absorption of the specific plastic chosen for the outlet insulator body and the lower the mass
of that plastic, the less the AC outlet will compress the dynamics and smear the transients of the audio components it is serving.
• Contacts: Outlet contacts are necessarily made of spring alloy sheet metal, either brass, phosphor bronze or beryllium copper. None of these
is as good sounding a conductor as pure copper; therefore, the shorter the contact strip, the better. Plating of the contact strip, no matter whether
it is platinum, palladium, rhodium or gold, always degrades the sound of the contact strip relative to a clean, bare contact; the thicker the plating, the worse. Contrary to widespread audiophile lore, more contact area does not improve sound; often it degrades sound. Thus, one-sided contacts sound better than two-sided contact clips. Because skin effect increases with conductor thickness, thinner contact strips yield deeper bass and cleaner highs—exactly the same sonic advantages that are observed in our super thin ribbon interconnects.
• Bus Bars/Conductors: Duplex wall outlets always have thick sheet alloy bus bars connecting the two halves of the outlet; both the thickness
(more skin effect) and the extra length of non-copper alloy conductor material degrade sound. Single AC outlets can connect their short contact strips
directly to copper wire, thus obviating the need for intervening bus bars.
• Faceplates: The less metal near the AC outlet, the better the sound. Apparently, the alternating electromagnetic fields around the outlet
power conductors induce eddy currents in metal outlet faceplates—and the energy lost to those eddy currents audibly compresses current peaks and smears
transients. Non-conducting faceplate materials yield better sound, provided a) they are not plastics with poor dielectric absorption; and b) the
material used is a good sink for draining power conductor vibrations out of the outlet.
Based on the above listening experiment findings, our Ultra-Minimalist AC Outlet design incorporates the following features:
• We use two single AC outlets whose insulation is a very low dielectric absorption polymer closely related to the best film capacitor
dielectrics—one that is far better sounding than the high absorption glass-filled nylon used in essentially all expensive high end duplex outlets.
Equally important, the combined mass of dielectric for the two single outlets is only one-third the mass of the glass-filled nylon insulators
in the expensive duplexes.
• Our design uses thin unplated brass contact strips solderlessly connected directly to copper conductors--sonically superior to any of the thick
plated strips plus thick plated bus bars used in the expensive duplex outlets. Even better, our strips are only 35% as long and half as thick as
the contact strips/bus bars inherent in the duplexes. One further advantage is that we use one-sided contacts as opposed to the two-sided contact
clips of the duplexes.
• We use a maple faceplat which a) provides an excellent sink for outlet vibrations instead of the usual thin stamped metal faceplates which add
resonances; and b) eliminates metal faceplate eddy currents while introducing far less dielectric absorption than any plastic or carbon fiber faceplates.
• To connect the copper conductors of our AC outlet to the house AC wires we provide special low dielectric absorption ceramic wire nuts instead of
the high absorption plastic wire nuts universally used by electricians installing residential power wiring.
• All components of our AC outlet are cryogenically treated.
Given the sizable combined effect of all these sonic advantages, it is not surprising that the Mapleshade Ultra-Minimalist AC Outlet has easily
prevailed in head-to-head listening tests with the most well-reviewed high end AC outlets, outlets costing up to $225 each.
1. Make absolutely sure that you have turned off the circuit breaker connected to the outlet you are replacing.
2. Unscrew the faceplate of the old outlet, then unscrew the two mounting screws above and below the outlet body.
3. Pull out the outlet body far enough that you can unscrew the three screws on the outlet body that fasten the white (neutral), black (hot),
and green (ground) wires of your house AC wiring. Discard the old outlet and faceplate.
4. One at a time, twist each of the new outlet’s three wires (each of these three outlet wires is actually two conductors twisted together) with
the matching color wire coming from the house AC system and secure each twisted-together bundle by screwing onto it one of the ceramic wire nuts.
Make absolutely sure you’ve mated green-to-green, white-to-white and black-to-black. (When ordering the Quad A/C Outlet, repeat the process
for the second set of wires).
5. Gently stuff all the wires back into the in-wall outlet mounting box. Then position the faceplate over the opening so that the faceplate’s two
holes line up with the two outlet mounting holes of the in-wall mounting box. Insert the two mounting screws and tighten moderately. Note: over-tightening
will crack the maple faceplate.
6. For the fanatical perfectionist: if you have plastic in-wall mounting boxes, either a) replace them with grounded metal boxes (ungrounded metal
near the power conductors induces extra sonic degradation); or b) even better, get rid of the in-wall box (metal or plastic) entirely. If you
undertake b), you will need to provide some kind of wood mounting strips for the faceplate screws.
||ANOTHER WONDROUS UPGRADE
|If your goal is to attain lifelike tonality then the minimalist AC wall outlet is an absolute must purchase. My Harmon Kardon 330c with factory power cord, conductors separated like Pierre suggests, now sounds very much like the Decware tube amp I used to own. I kid you not! Now I wonder if I get a Clearview power cord would I even feel the need to purchase another Decware tube amp.|
|- Kevin, TX|
||Hear Your System for the First Time
|Not including this AC outlet in your system is an audiophile crime! The impact is spectacular. This outlet replaced one that is highly rated and 4x the cost. The Mapleshade AC outlet removed veils of vaseline and let me hear what was intended. I am a truly satisfied customer and vote for this product as a must include in your system!|
||Great Duplex AC Outlet at Any Price!
|I have been experimenting with AC outlets for about nine years and have had a Shunyata Z1 for the last five years. With my positive history with Mapleshade and Omega Mikro, I thought I would give Pierres new AC outlet a try. The Mapleshade outlet exceeded my expectations! It truly refined the micro dynamics and three dimensional sense of the music compared to the Shunyata Z1. Congratulations on another fine audiophile product! Cheers!|
|- Scott Hays, CA|
||The last A/C outlet upgrade Im planning on making!
|I just installed the Ultra Minimalist Duplex outlet. FANTASTIC! Over the past 17+ years I must have tried almost every hi-end a/c outlet. Most had a somewhat questionable improvement if at all!
This product is the easiest to install, by far. It really does make an nice improvement over ANY I have used.
TIP: Once installed, try a counter-clockwise turn on the 2 plate screws - I seems that less tension on the wood plate may open-up the sound!|
|- Craig Konjoyan, CA|